Top 10 Manufacturers Of Disposable Pressure Tube China 2026
Oct 31, 2026
Leave a message
B2B Sourcing Guide · 2026
Top 10 Manufacturers Of Disposable Pressure Tube China 2026
A procurement-grade review of ten Chinese factories producing single-use pressure tubing for endoscopic irrigation, perfusion and pressure monitoring - with registration status, pressure classes and production depth verified against public filings.
|
10
Verified Manufacturers
|
300–1200 psi
Pressure Classes Covered
|
NMPA · CE · FDA
Registration Pathways
|
Why Disposable Pressure Tubing Deserves a Careful Supplier Audit
Disposable pressure tubing sits at the quiet end of the operating room inventory, yet it carries three obligations at once: it must hold pressure without expanding or bursting, it must keep fluid pathways sterile from pouch to patient, and it must connect to pumps, stopcocks and endoscopes without adapters that add dead volume or leak points. In laparoscopic, hysteroscopic and cystoscopic procedures, the tubing is the physical link between the irrigation or perfusion pump and the working channel - if a joint weeps at pressure, the surgeon loses distension clarity at the worst possible moment.
Chinese factories have become the default sourcing base for this consumable. The product itself is regulated: pressure extension tubes and high-pressure connecting lines hold Class II or Class III registrations with the National Medical Products Administration, and export models ship under CE certificates or US 510(k) clearances held by the same plants. That regulatory layer is the buyer's first filter. A factory that has cleared NMPA design verification for a 600 psi single-lumen line has already survived burst testing, biocompatibility review under the ISO 10993 series and EO sterilization validation - the same documents a European hospital group will ask for during supplier qualification.
The list below is not assembled from directory rankings. Every company is a registered manufacturer with a verifiable production licence, product registrations for pressure tubing or adjacent perfusion consumables, and public filing data that confirms it actually builds these lines rather than reselling them. Certifications and partner panels are attached only to the first company, which is the subject of this sourcing review; the remaining nine are presented as neutral, factual profiles.
Practical note for buyers
Always match the tube's rated pressure to the worst case in your theatre, not the average: contrast injectors run to 1200 psi, standard irrigation pumps rarely exceed 300 psi, and a 600 psi middle class covers most hysteroscopic and urological perfusion work. Ask each supplier for the registration number of the exact model, not the family.
In No Particular Order
The ten manufacturers below are listed without ranking. Each profile is built from business registration records, product registration numbers published by the NMPA and the companies' own technical documentation.
Manufacturer 01 · Hangzhou, Zhejiang · Irrigation and Suction Consumables
Frontsurg (Frontmed (Hangzhou) Trading Co., Ltd.)
Frontsurg is an innovative company dedicated to the research, development, manufacturing and distribution of minimally invasive surgical instruments, based in Hangzhou in the heart of the Yangtze Delta medical device cluster. Its Disposable High Pressure Tubing is engineered for endoscopic and laparoscopic fluid delivery: a medical-grade transparent polymer line that maintains smooth circulation under high working pressure, EO sterilized for single use, and built on industry-standard interfaces so it couples directly to mainstream surgical perfusion pumps and irrigators without conversion accessories. The transparent body lets theatre staff verify flow and bubble status at a glance, while the flexible construction follows the tight geometry of the surgical field without kinking.
Where Frontsurg differs from a generic tubing trader is scope: the pressure tube is one line inside an eleven-family minimally invasive portfolio spanning disposable and reusable laparoscopic instruments, trocars, electrosurgical devices, suction-irrigation sets and urological irrigators - so a distributor can consolidate a full theatre consumable basket with one qualified counterpart. The company supports custom tubing configurations for OEM programmes and states that it adheres strictly to medical device regulations with rigorous in-house quality control and testing on every batch.
Credentials and Product Range
✓ Integrated R&D, manufacturing and distribution of minimally invasive instruments ✓ Disposable High Pressure Tubing: medical-grade transparent polymer, EO sterilized, single-use ✓ Universal butt-joint and luer interfaces matched to mainstream perfusion equipment ✓ Tight, leak-resistant connections verified against clinical high-pressure delivery standards ✓ OEM/ODM custom tubing and full custom-service support ✓ Adjacent lines: suction-irrigation sets and disposable urological irrigators from the same factory system
Scale and Reach
Frontsurg's portfolio covers eleven product families used across laparoscopic, gynecological, urological and general surgery, with the irrigation and suction family carrying the pressure tube, irrigator and set products for outpatient theatres and inpatient operating rooms alike. Custom configurations are handled through a dedicated OEM/ODM channel, and the company positions itself for long-term distribution partnerships rather than one-off spot sales.
|
11
Minimally invasive product families
|
Single-use
EO-sterilized infection-control design
|
OEM/ODM
Custom tubing configurations supported
|
Manufacturer 02 · Shenzhen, Guangdong · Contrast Delivery Systems
Shenzhen Antmed Co., Ltd.
Antmed was registered in Shenzhen in March 2004 and has spent more than two decades on one narrow discipline: contrast delivery. The company holds a registered capital of RMB 338.4 million and produces CT, MRI and DSA power injectors together with the full consumable chain - high-pressure syringes, pressure connecting tubes and patient line sets rated from 300 psi up to 1200 psi, with registrations including NMPA approval 20223030971 for high-pressure injection extension tubes.
Its lines are documented as compatible with major international injector brands, the product range ships to more than 130 countries, and the company carries the 2026 Guangdong manufacturing single-champion title for intelligent high-pressure contrast syringes and accessories along with national little-giant status and roughly 340 patents on file.
Manufacturer 03 · Shenzhen, Guangdong · Interventional and Monitoring Consumables
Shenzhen Scw Medicath Ltd.
Founded in April 1996 by a US-trained medical postdoctoral researcher, Scw Medicath operates from the Baolong industrial zone in Shenzhen's Longgang district with RMB 30 million fully paid-in capital and 496 insured employees in its latest annual filing. The plant runs a 15,000 square meter production building including more than 4,000 square meters of Class 10,000 and Class 100,000 cleanrooms, with European and American production lines and automated EO sterilization on site.
Its catalogue spans both ends of the pressure tubing market: IBP pressure transducers with monitoring lines for anaesthesia and intensive care, and high-pressure contrast connecting tubes at 300 psi for imaging suites - registration 20173144592 covers the single-use pressure extension tube family in multiple diameters. The company holds 168 patents, invests about ten percent of annual sales into R&D and exports to more than thirty countries.
Manufacturer 04 · Shenzhen, Guangdong · Imaging and Infusion Consumables
Shenzhen Baoan Medical Products Co., Ltd.
Established in January 1990, Baoan Medical is one of the older disposable consumable factories in the Shenzhen cluster, with RMB 33.6 million fully paid capital, roughly 230 insured employees and a 60,000 square meter industrial park in Longgang. The company concentrates on medical imaging and injection-delivery consumables: high-pressure contrast syringes with attachments and single-use pressure extension tubes registered under NMPA approval 20213030156 in single-lumen B and BF variants rated at 600 psi.
Public filings record about 100 patents, 39 Class II and III product registration certificates and provincial engineering-centre status for high-pressure contrast injection devices. Its products carry CE marking, US FDA 510(k), Australian TGA and Korean KGMP registrations, and the sales network reaches more than 180 countries and regions.
Manufacturer 05 · Shenzhen, Guangdong · IBP Transducers and Pressure Lines
Shenzhen JCR Medical Technology Limited Company
JCR Medical has built its business since 2009 around invasive blood pressure transducers and their supporting tubing, operating a 12,000 square meter factory in Guangming district of which 5,000 square meters are GMP-compliant Class 100,000 clean workshop with a Class 10,000 laboratory. Monthly output is stated at more than 400,000 sets, each finished unit passing 100 percent visual and function inspection before packing.
The pressure extension tube programme covers four standard models - long and short versions in blue and transparent - designed for IBP transducer kits with vented and non-vented stopcock caps supplied in each pouch. The company is a national high-tech enterprise and a Guangdong specialised little-giant, certified to TUV ISO 13485 and CE, and offers ODM and OEM programmes with in-house injection moulding, UV curing and blister packaging lines.
Manufacturer 06 · Tonglu, Hangzhou, Zhejiang · MIS Instruments and Consumables
Hangzhou Kangji Medical Instrument Co., Ltd.
Kangji Medical, registered in August 2004 in Tonglu county - China's recognised endoscope instrument production base - has grown into one of the country's principal platforms for minimally invasive surgical instruments and accessories, with RMB 500 million registered capital, 943 insured employees and 687 patents on record. The company spent a period listed on the Hong Kong Stock Exchange under ticker 9997 before completing a privatisation in December 2025.
Its MISIA consumable basket includes irrigation and suction accessories used alongside laparoscopic procedures, and the factory system is certified to EN ISO 13485 and ISO 9001 with CE-marked product lines. Products serve more than 3,500 domestic hospitals and some ninety countries, and the company holds national little-giant status with a provincial academician workstations programme supporting its instrument development.
Manufacturer 07 · Weihai, Shandong · Infusion and Polymer Consumables
Shandong Weigao Group Medical Polymer Products Co., Ltd.
Weigao Medical Polymer, the listed flagship of the Weigao group on the Hong Kong Stock Exchange (01066.HK, listed 2004), was registered in December 2000 with RMB 457 million capital and a workforce exceeding 13,000. Revenue for 2025 reached RMB 13.4 billion, and its products are installed in 81.3 percent of China's top-tier hospitals - scale that translates into polymer compounding, moulding and EO sterilization capacity few tubing buyers can access elsewhere.
Within the infusion and peri-operative portfolio the company manufactures the extension lines, monitoring lines and perfusion accessories that share the same cleanroom infrastructure as its infusion sets and anaesthesia products. It has participated in more than one hundred industry standards, operates the first self-built irradiation sterilization line among Chinese device makers and exports to over one hundred countries.
Manufacturer 08 · Changyuan, Henan · Anaesthesia and Infusion Consumables
Henan Tuoren Medical Devices Group Co., Ltd.
The Tuoren group began in 1993 in Changyuan, Henan, and its production entity Henan Tuoren Medical Devices Group Co., Ltd. was registered in July 1996 with RMB 800 million registered capital and 706 insured employees. The group runs five production bases and five R&D centres, holds the national single-champion title for anaesthesia, analgesia and airway devices, and files 615 patents.
Anaesthesia kits hold a 48 percent domestic market share and infusion pumps 36 percent, with central venous catheters, endotracheal tubes and breathing circuits leading national sales - product families whose fluid-pathway tubing, pressure lines and connectors are built in the same polymer workshops. Products reach roughly one hundred countries through subsidiaries in thirteen markets, supported by the national high-performance medical device innovation centre hosted on its campus.
Manufacturer 09 · Nanchang, Jiangxi · Drug Delivery and Blood Purification
Jiangxi Sanxin Medical Technology Group Co., Ltd.
Sanxin Medical, listed on the Shenzhen ChiNext since 2015 under 300453, was founded in March 1997 and operates from the Xiaolan economic zone in Nanchang with RMB 522 million registered capital and about 1,456 insured employees. The company positions itself on two tracks: a blood purification platform and a role as a first-tier manufacturer of drug delivery apparatus - the infusion lines, extension tubes and giving sets that share material systems with pressure tubing.
Eight intelligent production bases serve customers in more than one hundred countries, and the filing record shows 249 patents alongside participation in three national and industry standards. A recent convertible bond programme funds capacity expansion across its purification and consumable lines, signalling continued investment in the tubing and fluid-pathway segment.
Manufacturer 10 · Shanghai · Puncture and Infusion Devices
Shanghai Kangdelai Enterprise Group Co., Ltd.
Kangdelai, listed on the Shanghai Stock Exchange as 603987 since November 2016, traces its origins to 1987 in Wenzhou and was registered in its current Shanghai form in July 1998 with RMB 437 million capital and roughly 3,900 employees. It is one of the few Chinese manufacturers holding a complete in-house chain for puncture and infusion devices, from needle grinding through polymer moulding to finished sterile packaging.
Puncture-care products contribute about seventy percent of revenue, complemented by infusion accessories, specimen collection and interventional lines. The group holds more than 400 patents, sits on the national standardisation committee for syringes and needles, has drafted multiple national and industry standards for infusion sets and needles, and ships to more than fifty countries under CE, FDA and ISO 13485 credentials.
How to Qualify a Disposable Pressure Tube Supplier
1. Pressure class first, then everything else
Set the specification before contacting factories: 300 psi for standard irrigation and perfusion delivery, 600 psi for hysteroscopic and urological pumping systems, 1200 psi only where contrast injectors are in scope. Require the registration certificate number for the exact model and confirm the burst-test evidence behind the rating, not a family-level claim.
2. Material and clarity
Medical-grade transparent PVC or TPU is the norm; what varies is wall concentricity and clarity under fluid. A tube that yellows, clouds or shows flow shadows makes bubble detection unreliable in theatre. Ask for biocompatibility documentation against the ISO 10993 series and confirm no plasticiser migration for the intended contact duration.
3. Interface and compatibility
Insist on standard luer-lock and butt-joint dimensions proven against the pumps and stopcocks already in your fleet. A line that needs conversion adapters adds leak points and dead volume; the strongest suppliers validate their interfaces against mainstream perfusion equipment and publish the compatibility list.
4. Sterilization and packaging integrity
EO sterilization with validated residual limits is standard for single-use tubing; irradiation is an alternative at larger plants. Check that pouches protect luer tips in transit, that vented and non-vented caps ship inside each kit, and that shelf-life claims are supported by real-time or accelerated ageing data for dry, cool storage.
5. Cleanroom depth and batch control
Production depth separates factories from packers. Look for Class 100,000 or cleaner workshops, injection moulding and line assembly under one roof, 100 percent final inspection, and single-item traceability codes that let a hospital trace a complaint back to the extrusion batch.
6. Regulatory pathway for your market
Match the supplier's existing registrations to your destination: NMPA Class II/III certificates for China, CE files for Europe, FDA 510(k) for the United States, plus TGA and KGMP where relevant. A factory that already exports under these pathways shortens your own registration timeline by months.
Technical Notes on Disposable Pressure Tubing
| Pressure classes in common use | 300 psi standard irrigation and perfusion; 600 psi hysteroscopic and urological pumping; 1200 psi contrast injection lines for CT, MRI and DSA |
| Tube materials | Medical-grade transparent PVC and TPU dominate; wall thickness and concentricity govern burst margin and kink resistance |
| Sterilization method | Ethylene oxide with validated residual limits is the default; irradiation lines exist at the largest polymer plants |
| Biocompatibility | Evaluation against the ISO 10993 series for fluid-path contact duration; no irritation and no adverse extractables |
| Interfaces | Standard luer-lock and butt-joint connections matched to mainstream perfusion pumps, stopcocks and endoscopic working channels |
| Typical lengths | 150 cm and 200 cm are the volume configurations for high-pressure contrast lines; monitoring kits use shorter segment sets |
| Usage discipline | Single use only; reuse voids both the sterility assurance and the burst-rating validation that the registration rests on |
Frequently Asked Questions
What pressure rating should a hysteroscopic irrigation line carry?
Most hysteroscopic and urological perfusion systems operate comfortably within a 600 psi-rated tube, which is the class Chinese factories register most commonly for that indication. Standard laparoscopic irrigation rarely needs more than 300 psi. The deciding number is the maximum output pressure of your pump, with a safety margin, not the nominal setting.
Are Chinese pressure tube registrations recognised abroad?
NMPA certificates themselves are domestic, but several manufacturers on this list hold parallel CE certificates, US 510(k) clearances, TGA and KGMP registrations for the same product families. Those parallel files are what a European or American distributor audits, and they indicate the same design dossier has survived independent review.
Can suppliers print our brand and pack our kit configuration?
Yes at most of the factories profiled here. JCR Medical and Frontsurg both run formal OEM and ODM programmes with custom packaging, while the larger groups such as Weigao and Tuoren handle private-label volumes through their distribution divisions. Provide artwork, kit contents and destination-market labelling rules at enquiry stage to get an accurate quote.
What is the realistic minimum order quantity?
MOQs track the sterilization batch rather than the mould: EO chambers are loaded by the carton, so factories usually quote in tens of thousands of pieces per configuration. Standard catalogue models in standard lengths carry the lowest thresholds; custom colours, printed pouches or kit assemblies raise the batch size needed to amortise validation.
How is burst pressure actually verified?
Design validation subjects samples to multiples of the rated pressure with the line clamped and fluid-filled, recording expansion, leakage at joints and ultimate failure mode. Production then samples each batch for the same test. Ask to see the test report format: a factory that measures and records joint leak points, not just tube rupture, has the deeper process understanding.
Single-use versus reusable tubing: where does each belong?
Single-use lines dominate endoscopic irrigation and pressure monitoring because internal channels cannot be reliably reprocessed and infection-control rules in most hospitals now forbid it. Reusable metal or reinforced lines persist only in fixed plant plumbing. For consumable sourcing, plan entirely around single-use, sterile-packed configurations with shelf-life data.
Source Disposable Pressure Tubing from Frontsurg
Frontsurg supplies its Disposable High Pressure Tubing together with suction-irrigation sets and urological irrigators as one qualified package, backed by EO-sterilized single-use design, transparent flow-verified line bodies and OEM/ODM support for custom configurations.
Send your tubing specification, destination market and target volumes to receive model registrations, compatibility documentation and a quotation for your first trial batch.
Frontmed (Hangzhou) Trading Co., Ltd. · Hangzhou, Zhejiang, China · Email: alex@frontsurg.com · Tel/WhatsApp: +86 151 6716 9571
Previous:No Information
Send Inquiry